she's finished, ship her
she's finished, ship her
Some more pics of progress to date some wiring to sort and need another cossie fuel pump
Pic 1 engine where @
Pic 2 Standard cossie pump against a phase 1 GTT pump
Pic 3 Modified T5 fuel rail with cossie injectors
Last edited by James5; 24-02-2009 at 00:17.
Nearly done mate. Days work by the looks of it.
Car looks well
Those 16v bonnets are in the fitting and finish dep't though eh.
The part was from Renault direct matey or if you have a local scrappy with some volvo F series 1.7 lumps in 440 etc..
7700716912 - Mounting Plate - £19.51 inc VAT
With ref to using the GTT plate not done it myself but you could prob place the engine in the car and place the gtt plate on the mount and drill an extra couple of holes into the plate so you could mount it to the 172 block may need a little more fettling than that. I purchased a new GTX plate from Renault but it was on delay for 2 weeks from france.
Have to agree do not like the 16v bonnet but it serving a purpose will hopefully look better once sprayed uptungy
Last edited by James5; 14-01-2009 at 22:47.
can you re-drill the GTT mounting, I was doing it so often I made up a drill template for them. from memory one hole lines up. you need to tweek it a bit with a grinder to clear the bottom water pipe.
Prob could have had it running by now but stumped with the wiring and awaiting a brand new 044 fuel pump to turn up I will get their eventually.
rear.. it would be too much work to do it normally ..if that makes sense
Still not running yet spent 2 hours with the car sorting incomplete bits out got perm live, ignition live, fuel pump is wired up everything seems to have power but I am unable to crank over as yet given up for now as to cold!
you can't get it to crank ? thats the easy bit surely
Well it's not the starter it's me being **** with electrics still can't get it to work
That's what I am going to do put some more earths on the block over the weekend
Last edited by James5; 23-01-2009 at 23:16.
To wet to play outside with the car
So I have been in the shed and modified the alt bracket so it doesn't catch on the cross member
All left to do know sort engine earths and get some 12mm bore fuel line.
And a quick pic of the engine as she is at the mo
Last edited by James5; 25-01-2009 at 17:31.
12mm bore line ? christ
just reduce it down, alot of the bigger pumps are like that. 8mm line will be fine.
Keep up the good work james mate. you will get there in the end.
8 mm copper pipe is cheap , sure its ok to use this, paint it with under seal when done . looks tidy.
Almost there just can't get the bitch to run at the mo
Starter engages, fuel pump sounding but nothing else is happening! oh well will try some more fettliong in a couple of days.
Going to check for spark if no spark looks like it could be my ECU not demobilised
does the fuel pump prime when you switch the key on ? does it then fire up again the moment you start cranking ?
i believe that if the ecu hasnt been decoded and u arent using the full 172 ignition system with key and everything then it wont work, the immobiliser will kick in. few people i know run this engine in their clios, i'll go investigate
yeah, could be the immo like coops is saying but I wonder if it would even let you prime the pump ? I would have guessed that it wouldn't do anything atall if it was an immo issue. maybe not ?
do you have a wiring diagram for it ? If you can post it up A) I'd find it quite helpfull since I don't have one and B) I'll go through it and tell you what I think you need to connect to what then you can compare with what you've done already
I have thought about the ECU itself but it was supposedly demobilised by RS tuning which I am going to call up and see what they say.
With ref to the wiring the only guide I have got is attached which is an allocationf ECU inouts and outputs most of the work has been done by the use of multimeter, continuity tester.
172 Fuel pump relay -
Red - perm live
Yellow - ign live
white - output to pump
violet - trigger from ecu
Last edited by James5; 01-02-2009 at 14:20.
According to the cliosport guys it should still crank if the immobiliser is active, just no fuel/spark.
if there was no immobiliser involved I'd have said look at your crank trigger to make sure it's OK and wired up properly, since if this doesn't work you won't get the pump running while you crank nor will you get a spark.
Just got some info back on cliosport ref the RS tuning ECU's -
http://www.cliosport.net/forum/showthread.php?t=390305
Apparently this member has heard of 'issues' with RSTuning decodes. They seem to require an emulator in addition to the decode almost as if the ECU will accept any imobiliser code, but it still needs *a* code, if that makes sense? iirc, both geesus and danlp6 had this issue
Beanie and I used www.ecuclinic.com and it came back plug and play if it's any use to you.
I will speak with rstuning ans see what they say if not going to have to get it decoded properly with the ecuclinic
This is not looking good with the ecu scoff did you ever get to play with ashys phase 1 ecu if so what was the outcome
Well got some news ref the ECU from the bloke @ RS tuning whom done the work who is also a cliosport member. He confirmed that the ECU I have needs to have an emulator to get it demobilised appartently mine was virginilised.
Anyone on here able to demobilise a phase 1 ECU???
does it turn over?
I just get the starter wanting to go and the fuel pump primes that is it.
What do you mean by the starter wanting to go?
Does the engine turn over on the starter?
Starter is turning but no fuel or spark which is apparently what the immobilser does.
I am now consdering going standalone as I will have to do this in the future anyway just funds at the mo are a little low
Last edited by James5; 01-02-2009 at 21:56.
Fancy a nice DTA E38 all mapped up with loom to suit a 172
Its a fecking pain in the arse it cost me over £100.00 to get that ECU and now to get it demobilised it's going to cost me over that . Should have gone standalone in the 1st place at this rate. Going to stick with the standard ECU for now and get it demobilised and when I go turbo hopefully go adaptronic.
it'll have had a hammer through it before I'm finnished with it to be fair, I'm probably just asking a bit too much of it with what I'm trying to do with it and I'd need a top of the range DTA or better before I got anywhere near the features I want. I think I've found a solution to my issue anyway
Phase 1 172 ECU Demobilised (emulator) & group N map